Weaving Those Squares Together: Part 2

I sat down again yesterday and wove squares together trying to make it look better and make decisions about those short corners. I did come up with a third bit of advice though while doing it.

Advice 3. They would work much better with a sticky grabby yarn. I’m using cotton crochet yarn as it is easy to see what is happening, alas it also shifts very easily and can go wonky easily. I think a nice grabby wool with all those barbs helping out would keep the yarn in place better.

Next just a bit about how I finish squares. I know “they” tell you to just bring those two tails back in over and under a couple of wefts and then cut them off. For me (being me) that just looks a bit odd. Just this short thick bit that stands out. Like a mistake. But I also have a tendency towards over kill on making things secure. When I package a box to mail, you can bet there is tape everywhere, and the poor person getting the box will have a time breaking into it. But my goal is that nothing in transit will break into it as well. So back to the squares. I take those tails and weave them all the way across before cutting them off. So you will see that on two sides of each square that last thread is doubled and two sides it is not.

So one last comment before starting. Remember from yesterdays post to cut your yarn before starting. It calls for 8 yards for the full square, so cut two 4 yard lengths and start with one of them. When getting near the end use a Russian Join to connect them and continue on weaving.

IMG_7448

Square and loom lined up matching pins and first layer laid in

The first step in weaving two squares together is to make sure that you line up sides to match. If you look at the loom on each side there will be 3 pins at one end and 2 pins at the other end. Those two pins match to two pins on the touching side and they create two loops that go around the corner. So be sure that when you lay the loom and square down together that the 3 pins match up to 2 loops that are all committed to that side (the top of the photo) and the 2 pins are match up to the two loops that come around the corner (bottom of the photo).

Also you can see that in this first photo I have already laid in the first layer. It is easier to lay the square and loom together so that the first layer you can just lay in and then only have half the length of yarn to weave through loops on the second layer. You can even flip the finished square over if needed to get it to line up for you. Yes, that took me a bit longer than it should have to figure out.

IMG_7449

Second layer begun. Circle top two pins in group and catch top loop

After the first layer is laid in then you start the second layer the normal way. When you get to your finished square, I find it easier to catch the loop after I have the yarn between its proper pins and heading back for the next weft. So on this second layer you are wrapping the yarn around the top and middle pin in each group (per my photo) so the loop, from each group of the finished square, you want to catch is the top one that corresponds.

IMG_7453

Second layer completed and left loops all caught

Now in the above photo the second layer is completed.You can see at the far left that where the two pins are I only caught the loop that is on that side and not the one that technically faces the left side of the square (as opposed to top per photo). I have done this several ways and still fiddling with it.

IMG_7455

Third layer complete

Now with this photo you can see that the third layer is laid in as you would if doing a normal square by itself. Nice to have an easy run again. If you look closely at the top left you can see where my Russian join is. Not as nice a one as my illustration yesterday, but maybe that is so you can tell it is there. I have also started the needle down for that fourth layer. Remember here is where you start weaving over under every other warp thread, and we are finally creating a woven piece that won’t come apart. I am still amazed at whoever dreamed this whole process up first and figured out that you could weave this way.

IMG_7458

Now picking up the bottom loop of finished square

When weaving the fourth layer and you come to the finished square, you will pick up that other loop in each pair. So now we come around the bottom two pins in each group and going over the other, we will then start weaving over and under the warp threads as we head back down the row. Now it is easier to see why you pick up which loop you do in each pair as they line up.

IMG_7461

Finished fourth layer and weaving in tails

Once you have woven all 16 wefts in then you weave in your tails as much as you want. I did catch that same loop again that we caught on the second layer. The one of the two that go around the corner that is more to this side.

IMG_7463

Finished! 

Ok, yes, it does need to be taken off the loom and tails cut but those pictures didn’t make the grade. And yes, I know there is a bit of fuzziness to these so you can only guess how bad those were.

Next we will add a square into that spot at the top and have two sides to weave into it. Fun!

Advertisements
Categories: Weaving | Tags: , , | 1 Comment

Post navigation

One thought on “Weaving Those Squares Together: Part 2

  1. Challenging idea. I would have probably started with all 8 yards on the needle… thanks for the tips.
    Diane

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Create a free website or blog at WordPress.com.

%d bloggers like this: